柱塞孔径向位置误差对缸体倾覆力矩的影响

兰州理工大学学报 ›› 2025, Vol. 51 ›› Issue (1): 34-44.

柱塞孔径向位置误差对缸体倾覆力矩的影响

王建森^*1,2, 黄伟¹, 李文宣¹, 雷震宇¹, 田世荣¹

1.兰州理工大学能源与动力工程学院, 甘肃兰州 730050;
2.兰州理工大学甘肃省液压气动工程技术研究中心, 甘肃兰州 730050

收稿日期:2022-08-15 出版日期:2025-02-28 发布日期:2025-03-03
通讯作者: 王建森(1973-),男,甘肃华池人,博士,副教授.Email:wajase@163.com
基金资助:
甘肃省科技计划资助(17JR5RA120)

Influence of the radial position error of plunger hole on overturning moment of cylinder block

WANG Jian-sen^1,2, HUANG Wei¹, LI Wen-xuan¹, LEI Zhen-yu¹, TIAN Shi-rong¹

1. School of Energy and Power Engineering, Lanzhou University of Technology, Lanzhou 730050, China;
2. Hydraulic and Pneumatic Engineering Technology Research Center, Lanzhou University of Technology, Lanzhou 730050, China

Received:2022-08-15 Online:2025-02-28 Published:2025-03-03

摘要/Abstract

摘要： 以高速斜盘式轴向柱塞泵为研究对象,建立了考虑由柱塞滑靴组件和柱塞孔内油液质量引起惯性力、中心弹簧力、柱塞底部油液压力和配流副油膜支撑力的缸体倾覆力矩模型,计算分析了在额定工况点柱塞孔径向分布位置随机误差和确定误差下缸体附加倾覆力矩的大小及其变化规律.结果发现:在图纸允许径向分布位置误差±0.1 mm的情况下,与理想状况相比,随机误差为±0.1 mm时,惯性力引起的绕x轴最大力矩脉动为1.16%;支反力引起的绕x、y轴最大力矩脉动均为0.64%;确定误差为±0.1 mm时,惯性力引起的绕x、y轴附加倾覆力矩为恒值;支反力引起的绕x轴最大力矩脉动为0.05%,绕y轴最大力矩脉动为0.45%.

关键词: 高速, 斜盘式轴向柱塞泵, 缸体倾覆力矩, 径向位置误差

Abstract: Taking a certain type of high-speed swash plate axial piston pump as the research object, a model for cylinder overturning moment that incorporates the inertia force caused by the mass of the piston-slipper assembly and the oil within the piston bore, the central spring force, the oil pressure at the bottom of the plunger, and the supporting force of the valve plate oil film were established. Based on the cylinder overturning moment model under the oil film support force, the random error of the radial distribution position of the plunger hole at the rated operating point and the size and variation law of the additional overturning moment of the cylinder under the definite error are calculated and analyzed. The results show that, within the permissible radial position error of ± 0.1 mm, compared with the ideal situation, the maximum moment fluctuation about the x-axis due to inertial forces is 1.16% when the random error is within ±0.1 mm, while the maximum moment fluctuation about both the x-and y-axes due to the supporting reaction force is 0.64%. For a deterministic error of ±0.1 mm, the additional overturning moments around the x and y axes caused by the inertial force is constant, whereas the maximum moment pulsation around caused by the support reaction force is0.05% about the x-axis and 0.45% about the y-axis.

Key words: high speed, swash plate axial piston pump, cylinder overturning moment, radial position error

中图分类号:

TH137

王建森, 黄伟, 李文宣, 雷震宇, 田世荣. 柱塞孔径向位置误差对缸体倾覆力矩的影响[J]. 兰州理工大学学报, 2025, 51(1): 34-44.

WANG Jian-sen, HUANG Wei, LI Wen-xuan, LEI Zhen-yu, TIAN Shi-rong. Influence of the radial position error of plunger hole on overturning moment of cylinder block[J]. Journal of Lanzhou University of Technology, 2025, 51(1): 34-44.

参考文献

[1] 吕飞,徐兵,张军辉.转速对EHA泵柱塞副柱塞位姿及泄漏量影响仿真分析[J].机械工程学报,2018,54(20): 123-130.
[2] HONG Y S,DOH Y H.Analysis on the friction losses of a bent-axis type hydraulic piston pump[J].Journal of Mechanicals Science and Technology,2004,18(9):1668-1679.
[3] 刘巧燕,闻德生,高俊峰.双定子力平衡轴向柱塞泵及其流量波动性分析[J].中国机械工程,2017,28(2):228-232.
[4] 聂松林,李硕,尹方龙,等.水液压泵柱塞套变形特性的流固耦合研究[J].中国机械工程,2020,31(10):1135-1141.
[5] 闫政,权龙,黄家海.变转速变排量双控轴向柱塞泵脉动特性及噪声研究[J].机械工程学报,2016,52(16):176-184.
[6] 单增海,李志远,张旭,等.基于多传感器信息融合和多粒度级联森林模型的液压泵健康状态评估[J].中国机械工程,2021,32(19):2374-2382.
[7] KUNKIS M,WEBER J.Experimental and numerical assessment of an axial pistonpump's speed limit[C]//BATH/ASME 2016 Symposium on Fluid Power and Motion Control.Bath,UK:Professional Engineering Publishing,2016:1790-1798.
[8] CHAO Q,ZHANG J H,XU B,et al.Centrifugal effects on cavitation in the cylinder chambers for high-speed axial piston pumps[J].Meccanica,2019,54(6):815-829.
[9] ZHANG J H,LI Y,XU B,et al.Experimental study on the influence of the rotating cylinder block and pistons on churning losses in axial piston pumps[J].Energies,2017,10(5):1-15.
[10] ZHANG J H,CHEN Y,XU B,et al.Effect of surface texture on wear reduction of the tilting cylinder and the valve plate for a high-speed electro-hydrostatic actuator pump[J].Wear,2018,414:68-78.
[11] 张加桢,陆山,崔伟军,等.航空柱塞式油泵ZB-16D柱塞腔壁贯穿故障分析[J].航空学报,1993,14(4):153-158.
[12] XU B,CHAO Q,ZHANG J H,et al.Effects of the dimensional and geometrical errors on the cylinder block tilt of a high-speed EHA pump[J].Meccanica,2017,52(10):2449-2469.
[13] ZHANG J H,CHAO Q,XU B,et al.Effect of piston-slipper assembly mass difference on the cylinder block tilt in a high-speed electro-hydrostatic actuator pump of aircraft[J].International Journal of Precision Engineering and Manufacturing,2017,18(7):995-1003.
[14] 范文,孙海洋.机械加工工艺对零件加工精度的影响[J].机械设计,2021,38(增刊1):248-249.
[15] 王建森,刘耀林,魏列江,等.轴向柱塞变量泵偏置斜盘力矩分析[J].兰州理工大学学报,2017,43(3):44-49.
[16] MANRING,N D.Tipping the cylinder block of an axial-piston swash-plate type hydrostatic machine[J].Journal of Dynamic Systems,Measurement and Control,Transactions of ASME,2000,122(1):216-221.
[17] 曹伟栋.高速斜盘式轴向柱塞泵惯性力对若干零部件受力的影响[D].兰州:兰州理工大学,2021.
[18] 王彬,周华,叶志锋.燃油柱塞泵配流机构泄漏模型[J].南京航空航天大学学报,2011,43(2):172-177.