DP-TIG高速焊接工艺研究

兰州理工大学学报 ›› 2020, Vol. 46 ›› Issue (6): 33-37.

DP-TIG高速焊接工艺研究

刘自刚^1,2, 陈飞², 唐海鸿^1,2, 陈亮¹

1.诺力智能装备股份有限公司, 浙江湖州 313100;
2.浙江省智能物流装备工程技术研究中心, 浙江湖州 313100

收稿日期:2020-03-04 出版日期:2020-12-28 发布日期:2021-01-07
作者简介:刘自刚(1985-),男,河南夏邑人,工程师

Study on high speed welding technology of DP-TIG

LIU Zi-gang^1,2, CHEN Fei², TANG Hai-hong^1,2, CHEN Liang¹

1. Noblelift Intelligent Equipment Co. Ltd., Huzhou 313100, China;
2. Engineering Research Center of Intelligent Logistics Equipment of Zhejiang Province, Huzhou 313100, China

Received:2020-03-04 Online:2020-12-28 Published:2021-01-07

摘要/Abstract

摘要： 深熔钨极气体保护焊(deep penetration TIG welding,DP-TIG焊)具有焊接熔深大的优点,在厚板焊接领域具有极大优势.为了拓展DP-TIG焊在薄板高速焊领域的应用,分别针对低碳钢和不锈钢板材,调整焊接电流、焊接速度、钨极锥角、气体成分等工艺参数,进行了薄板高速焊接工艺研究.结果表明:相对常规TIG焊,对于2 mm厚的低碳钢板焊接速度提高了75%,对于3 mm厚的不锈钢板,焊接速度提高了2倍多,并且随着钨极角度的减小,焊接速度可以进一步提高,如果保护气体中引入一定量的H₂可以进一步提高不锈钢DP-TIG焊的最大焊接速度.

关键词: 不锈钢, 低碳钢, DP-TIG高速焊, 钨极锥角, 保护气成分

Abstract: Deep Penetration TIG welding (DP-TIG welding) takes the advantage of deep penetration welding and has great advantages in the field of thick plate welding. In order to expand applications of DP-TIG welding in the field of high-speed welding of thin plates, the high-speed welding process of thin plates made of low carbon steel and stainless steel was investigated in this research by adjusting welding current, welding speed, tungsten cone angle, gas composition and other process parameters. The experimental results show that compared with conventional TIG welding, the welding speed of low carbon steel plate with 2 mm thickness is increased by 75%, and for stainless steel plate with 3 mm thickness, the welding speed is increased by more than 2 times. Moreover, with the decrease of tungsten electrode angle, the welding speed can be further improved. If a certain amount of H₂ is introduced into the shielding gas, the maximum welding speed of stainless steel DP-TIG welding may be improved further to a certain extend.

Key words: stainless steel, low carbon steel, DP-TIG high-speed welding, angle of tungsten electrode, component of shielding gas

中图分类号:

TG403

刘自刚, 陈飞, 唐海鸿, 陈亮. DP-TIG高速焊接工艺研究[J]. 兰州理工大学学报, 2020, 46(6): 33-37.

LIU Zi-gang, CHEN Fei, TANG Hai-hong, CHEN Liang. Study on high speed welding technology of DP-TIG[J]. Journal of Lanzhou University of Technology, 2020, 46(6): 33-37.

[1]	赵吉鹏,王军,刘天增,李俊琛,冯力. 347H不锈钢电化学腐蚀行为研究[J]. 兰州理工大学学报, 2021, 47(6): 6-14.
[2]	唐梦兰, 王军, 刘天增, 李俊琛, 冯力. 热处理对硝酸熔盐中347H不锈钢腐蚀行为的影响[J]. 兰州理工大学学报, 2021, 47(5): 1-9.
[3]	俞树荣, 程月, 何燕妮, 宋伟. SAF 2707HD旋转弯曲疲劳性能[J]. 兰州理工大学学报, 2021, 47(2): 168-172.
[4]	喇培清, 石玉, 汪科良, 盛捷, 李正宁, 周学渊. 热轧变形量对铝热法制备的 2507双相不锈钢组织和力学性能的影响[J]. 兰州理工大学学报, 2020, 46(4): 1-5.
[5]	兰晔峰, 王创造, 胡秋晨, 胡巍巍, 李庆林. 奥氏体不锈钢离子渗N组织及性能[J]. 兰州理工大学学报, 2020, 46(1): 7-12.
[6]	李庆林, 赵尚, 胡秋晨, 胡巍巍, 兰晔峰. 316奥氏体不锈钢渗N/镀CrN复合改性层组织与性能[J]. 兰州理工大学学报, 2020, 46(1): 13-19.