纳米多晶强化K4169合金的组织和力学性能

兰州理工大学学报 ›› 2021, Vol. 47 ›› Issue (4): 1-5.

• 材料科学与工程 • 下一篇

纳米多晶强化K4169合金的组织和力学性能

李亚敏^*, 周生睿, 胡伟

兰州理工大学省部共建有色金属先进加工与再利用国家重点实验室, 甘肃兰州 730050

收稿日期:2020-10-12 出版日期:2021-08-01 发布日期:2021-09-07
通讯作者: 李亚敏(1973-),女,河北蠡县人,博士,副教授.Email:leeyamin@163.com

Microstructure and properties of K4169 superalloy with nano polycrystalline reinforcement

LI Ya-min, ZHOU Sheng-rui, HU Wei

State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metals, Lanzhou Univ. of Tech., Lanzhou 730050, China

Received:2020-10-12 Online:2021-08-01 Published:2021-09-07

摘要/Abstract

摘要： 采用手工电弧炉熔炼、水冷铜模冷却制备了K4169合金.利用X射线衍射、扫描电镜、透射电镜等对铸态及标准热处理态合金的组织进行了研究,并对标准热处理态合金的力学性能进行了测试.结果表明:铸态K4169合金为非晶-纳米晶材料,晶内析出相非常细小,小于10 nm;合金经标准热处理后,γ″相和γ′相以纳米多晶的形式析出;由于纳米多晶的强化作用,合金的断裂强度σ_b达到了1 203.91 MPa,屈服强度σ_0.2为818.93MPa,延伸率δ为16.8 %,硬度则达到了112.4 HRB,合金拉伸断口特征符合韧性断裂机制.

关键词: K4169高温合金, 组织, 纳米多晶, 力学性能, 拉伸断口

Abstract: A manual electric arc furnace andwater-cooled copper mould were used to prepare superalloy K4169. The microstructure of the alloy as-cast and standard heat treatment was examined by XRD, SEM, TEM, and the mechanical properties of the standard heat treated alloy were tested. The results show that as-cast K4169 alloy is amorphous-nanocrystalline material, the precipitation in grain is very fine and smaller than 10nm. The γ″ and γ′ phase are precipitated as nano polycrystalline after standard heat treatment the alloy. Because of the reinforcement by nano polycrystalline, the fracture strength σ_b of alloy can reach 1 203.91 MPa, and the yield strength σ_0.2 is 818.93 MPa, while the elongationδ is 16.8%, and the hardness reaches 112.4 HRB, and the tensile fracture characteristics conform to the ductile fracture mechanism.

Key words: K4169 Superalloy, microstructure, nano polycrystalline, mechanical properties, tensile fracture

中图分类号:

TG132.2

李亚敏, 周生睿, 胡伟. 纳米多晶强化K4169合金的组织和力学性能[J]. 兰州理工大学学报, 2021, 47(4): 1-5.

LI Ya-min, ZHOU Sheng-rui, HU Wei. Microstructure and properties of K4169 superalloy with nano polycrystalline reinforcement[J]. Journal of Lanzhou University of Technology, 2021, 47(4): 1-5.

参考文献

[1] BIRRINGER R.Nanocrystalline materials [J].Materials Science and Engineering A,1989,117(1):33-43.
[2] MEYERS M A,MISHRA A,BENSON D J.Mechanical properties of nanocrystalline materials [J].Progress in Materials Science,2006,51(4):427-556.
[3] KOCH C C.Nanostructured materials:processing,properties and potential applications [M].Norwich:New York Noyes Publications,2002.
[4] 李爱兰,汤鑫,盖其东,等.热处理工艺对K4169合金微观组织的影响 [J].航空材料学报,2006,26(3):311-312.
[5] RADAVICH J F,FORT A.Effects of long time exposure in alloy 625 at 1 200 ℉,1 400 ℉ and 1600 ℉ [C]//In Proceedings of the International Symposium on Superalloys 718,625,706 and Various Derivatives,TMS,Pittsburgh,Pennsylvania,1994.
[6] 汤鑫,曹腊梅,盖其东,等.K4169合金整体导向环精铸技术及热处理工艺研究 [J].宇航材料工艺,2007(6):82-86.
[7] EWING B A,GREEN K A.Polycrystalline grain controlled castings for rotating compressor and turbine components [C]//Superalloys 1984.New York:The Metallurgical Society of AIME,1984.
[8] NAZMY M,WEISS B,STICKLER R.The effect of advanced fine grain casting technology on the static and cyclic properties of IN713LC [C] // High Temperature Materials for Power Engineering 1990 Ⅱ.The Netherlands:Kluwer Academic Publishers,1990:1397-1404.
[9] 熊玉华,杨爱民,李培杰,等.K4169高温合金组织细化研究 [J].航空材料学报,2001,21(3):24-28.
[10] VALIEV R Z,ALEKSANDROV I V.Nanostructured materials obtained by severe plastic deformation [J].Nanostructured Materials,1999,12:35-40.
[11] VALITOV V A,MUKHTAROV S K,ZHILYAEV A P,et al.Evolution of microstructure during low temperature superplastic deformation of bulk nanostructured Ni-Cr-Fe-Nb superalloy [J].Reviews on Advanced Materials Science,2010,25(2):148-154.
[12] MUKHTAROV S K,ERMACHENKO A G.Influence of severe plastic deformation and heat treatment on microstructure and mechanical properties of a nickel-iron based superalloy [J].Reviews on Advanced Materials Science,2012,31(2):151-156.
[13] VALITOV V A,MUKHTAROV S K,RASKULOVA Y A.Formation of a nanocrystalline structure upon severe thermomechanical treatment and its effect on the superplastic properties of a nickel alloy with nonisomorphic second-phase precipitates [J].The Physics of Metals and Metallography,2006,102(1):105-113.
[14] MUKHTAROV S K,VALITOV V A,DUDOVA N R.Thermal stability and mechanical properties of nanostructured nickel based alloy inconel 718 [J].Reviews on Advanced Materials Science,2010,25(3):219-224.

纳米多晶强化K4169合金的组织和力学性能

Microstructure and properties of K4169 superalloy with nano polycrystalline reinforcement

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 12

编辑推荐

Metrics

本文评价

[1]	毕广利, 陈思琦, 姜静, 李元东, 张于胜, 蒋春宏. 滑动摩擦加工挤压Mg-Dy-Ni合金的显微组织、力学及腐蚀性能[J]. 兰州理工大学学报, 2021, 47(4): 13-21.
[2]	尹燕, 董开基, 李治恒, 薄尧, 路超, 张瑞华. 紧耦合真空气雾化制备Fe-Cr合金粉末的特性表征[J]. 兰州理工大学学报, 2021, 47(3): 10-14.
[3]	陈剑虹, 肖乐, 陈永庆, 闫英杰, 曹睿. 热等静压保温温度对TC4合金组织及拉伸性能的影响[J]. 兰州理工大学学报, 2021, 47(1): 1-4.
[4]	刘建军, 吕姝玥, 曾宝根, 兰晔峰, 李庆林. 稀土Y对Al-8%Mn合金微观组织和性能的影响[J]. 兰州理工大学学报, 2021, 47(1): 11-15.
[5]	毕广利, 徐作成, 顾家睿, 姜静, 蒋春宏, 李元东. Mg-7Sn-Zn(Y)合金的显微组织、时效硬化行为及力学性能[J]. 兰州理工大学学报, 2020, 46(6): 1-8.
[6]	黄勇, 严晓娟, 冉小龙. 压缩/直径比对纯铜对接冷压焊焊接接头的影响[J]. 兰州理工大学学报, 2020, 46(6): 28-32.
[7]	喇培清, 王娇, 肖海波, 郑月红, 杨理洁, 盛捷. MoCrFeMnNi高熵合金退火后的组织和性能[J]. 兰州理工大学学报, 2020, 46(5): 1-6.
[8]	冯力, 王军, 朱昶胜, 仲军和, 安国升. 横向约束对Fe-C合金凝固微观组织的相场法模拟[J]. 兰州理工大学学报, 2020, 46(5): 13-20.
[9]	顾玉芬, 耿培彪, 石玗, 李广, 郭晋昌. 光纤激光氮化处理对TC4合金组织和性能的影响[J]. 兰州理工大学学报, 2020, 46(4): 10-14.
[10]	乔宏霞, 彭宽, 陈克凡, 李江川, 洪芬. 陶瓷再生混凝土力学性能及微观结构分析[J]. 兰州理工大学学报, 2020, 46(3): 122-126.
[11]	赵燕春, 蒋建龙, 毛瑞鹏, 孙浩, 寇生中. Zr原子分数对Ti基非晶复合材料腐蚀性能的影响[J]. 兰州理工大学学报, 2020, 46(2): 7-12.
[12]	季根顺, 赵浩, 贾建刚, 张胜, 李周, 郝相忠. 定向脉冲气流TG-CVI法致密C/C复合材料工艺及性能[J]. 兰州理工大学学报, 2020, 46(1): 20-23.