6082铝合金摩擦塞补焊接头焊核区晶体特征

兰州理工大学学报 ›› 2022, Vol. 48 ›› Issue (3): 7-12.

6082铝合金摩擦塞补焊接头焊核区晶体特征

李德福^1,2,3, 王希靖^*1,2

1.兰州理工大学省部共建有色金属先进加工与再利用国家重点实验室, 甘肃兰州 730050;
2.兰州理工大学材料科学与工程学院, 甘肃兰州 730050;
3.兰州交通大学铁道技术学院, 甘肃兰州 730070

收稿日期:2021-11-03 出版日期:2022-06-28 发布日期:2022-10-09
通讯作者: 王希靖(1956-),男,甘肃兰州人,教授,博导.Email:wangxj@lut.edu.cn
基金资助:
国家自然科学基金(2012ZX04008011),甘肃省高等学校创新基金(2021A-045)

Crystal characteristics of nugget zone of friction plug welded joints for 6082 aluminum alloy

LI De-fu^1,2,3, WANG Xi-jing^1,2

1. State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metals, Lanzhou Univ. of Tech., Lanzhou 730050, China;
2. School of Materials Science and Engineering, Lanzhou Univ. of Tech., Lanzhou 730050, China;
3. School of Railway Technology, Lanzhou Jiaotong University, Lanzhou 730070, China

Received:2021-11-03 Online:2022-06-28 Published:2022-10-09

摘要/Abstract

摘要： 为降低对设备要求,在填充式搅拌摩擦焊匙孔修复技术的基础上,采用摩擦辅助加热的方法对6082铝合金匙孔类体积型缺陷进行了摩擦塞补焊试验,得到了成形良好的塞补焊接头.对接头焊核区进行EBSD分析.结果表明:晶粒细化显著,存在明显择优取向.塞棒转速由1 800 r/min增加至2 000 r/min,晶粒形状由等轴晶转变为线锤状,平均晶粒尺寸增大,大角度晶界组分略有降低;焊核区存在变形、剪切及再结晶混合织构,再结晶织构组分随转速增加而增加,由速度增加对变形速率产生的影响降低,相应地由速度增加对再结晶所产生的影响被强化.

关键词: 辅助加热, 摩擦塞补焊, 择优取向, 织构

Abstract: In order to reduce the requirements of equipment, on the basis of friction stir welding filling technology with solid state joining, the friction plug repair welding tests were carried out by shoulder auxiliary heating methods for 6082 aluminum alloy, and well-formed repair welding joints were obtained. EBSD analysis of nugget zone of joint shows that the grain refinement is significantand there is obviouspreferred orientation. With the increase of rotating speed from 1 800 r/min to 2 000 r/min, the grain shape changes from equiaxed grain to linear hammer, the average grain size increases, and thecomposition of high-angle grain boundary decreases slightly. The mixed texture of deformation, shear and recrystallization is found in the nuggest zone, and the composition of recrystallization texture increases with the increase of rotational speed. With the increase of the rotating speed, the effectof the increasing speed on the deformation rate decreases, while the effectof the increasing speed on the recrystallization increasesaccordingly.

Key words: auxiliary heating, friction plug welding, preferred orientation, texture

中图分类号:

TG453.9

李德福, 王希靖. 6082铝合金摩擦塞补焊接头焊核区晶体特征[J]. 兰州理工大学学报, 2022, 48(3): 7-12.

LI De-fu, WANG Xi-jing. Crystal characteristics of nugget zone of friction plug welded joints for 6082 aluminum alloy[J]. Journal of Lanzhou University of Technology, 2022, 48(3): 7-12.

参考文献

[1] BARMOUZ M,SHAHI P,ASADI P.Friction stir welding/processing of polymeric materials [J].Advances in Friction-Stir Welding and Processing,2014,1(4):601-670.
[2] 王国庆,赵刚,郝云飞,等.2219铝合金搅拌摩擦焊缝匙孔形缺陷修补技术 [J].宇航材料工艺,2012,42(3):24-28.
[3] 计鹏飞,刘西伟,张玉常,等.20 mm厚2219铝合金可回抽搅拌摩擦焊接及接头组织和性能分析 [J].焊接学报,2021,42(2):86-91.
[4] 周利,周炜璐,张嘉伦,等.搅拌摩擦焊匙孔修复技术研究现状 [J].航空制造技术,2016(14):75-79.
[5] 赵衍华,刘景铎,朱瑞灿,等.补焊技术的新突破——摩擦塞补焊 [J].焊接,2009(9):16-21.
[6] 黄永宪,韩冰,吕世雄,等.基于固态连接原理的填充式搅拌摩擦焊匙孔修复技术 [J].焊接学报,2012,33(3):4-8.
[7] 张忠科,赵早龙,李德福,等.6082铝合金摩擦塞补焊接头微观组织与性能 [J].材料导报,2020,34(16):16094-16099.
[8] 栾国红,季亚娟,董春林,等.LY12铝合金摩擦塞焊接头组织分析 [J].焊接学报,2006,27(10):1-3.
[9] BEAMISH K.Friction taper plug welding of 10 mm AA6082-T6 [R].Cambridge,UK:The Welding Institute,2003.
[10] METZ D F,WEISHAUPT E R,BARKEY M E,et al.A microstructure and microhardness characterization of a friction plug weld in frictionstir welded 2195 Al-Li [J].Journal of Engineering Materials & Technology,2012,134(2):1-7.
[11] METZ D F,BARKEY M E.Fatigue behavior of friction plug welds in 2195 Al-Li alloy [J].International Journal of Fatigue,2012(43):178-187.
[12] 刘凯旋,孙转平,杨新岐,等.铝合金搅拌摩擦焊缝摩擦塞补焊组织与力学性能 [J].焊接学报,2019,40(6):124-131.
[13] 杜波,孙转平,杨新岐,等.异种铝合金摩擦塞补焊接头微观组织及性能 [J].机械工程学报,2017,53(4):43-48.
[14] BO D,SUN Z,YANG X,et al.Characteristics of friction plug welding to 10 mm thick AA2219-T87 sheet:Weld formation,microstructure and mechanical property [J].MaterialsScience & Engineering A,2016(654):21-29.
[15] 刘敬萱,沈健,李锡武,等.焊接速度对6005A-T5铝合金搅拌摩擦焊接头组织演变及力学性能的影响 [J].稀有金属材料与工程,2019,48(12):3797-3805.
[16] 张亮亮,王希靖,刘骁.6082-T6铝合金搅拌摩擦过程中动态再结晶方式对焊核区织构类型的影响 [J].材料导报,2019,33(4):665-669.
[17] PENG C A,SZ A,JING C A,et al.Effect of rotation speed on microstructure evolution and mechanical properties of nugget zone in 2195-T8 Al-Li alloy friction stir welding joints-science direct [J].Materials Characterization,2021(176):1-14.
[18] HU Y,LIU H,FJJII H,et al.Effect of ultrasound on microstructure evolution of friction stir welded aluminum alloys[J].Journal of Manufacturing Processes,2020(56):362-371.
[19] 刘超,王鑫,门月,等.Ti-6Al-4V合金热压缩过程中的动态再结晶 [J].材料研究学报,2021,35(8):583-590.
[20] LIU X,ZHEN Y,SUN Y,et al.Local inhomogeneity of mechanical properties in stir zone of friction stir welded AA1050 aluminum alloy [J].Transactions of Nonferrous Metals Society of China,2020,30(9):82-93.
[21] 王猛,王舜,冯小亮,等.基于动态再结晶软化机制的H90黄铜高速摩擦磨损数值模拟 [J].塑性工程学报,2021,28(9):177-183.
[22] 戚文军,龚晓毅,黄正华.生物医用Mg-6Zn-xGd合金的挤压组织与腐蚀性能 [J].稀有金属材料与工程,2016,45(10):2609-2614.
[23] FONDA R W,BINGERT J F.Texture variations in an aluminum friction stir weld [J].Scripta Materialia,2007,57(11):1052-1055.
[24] SHEN J,WANG F,SUHUDDIN U F H,et al.Crystallographic texture in bobbin tool friction-stir-welded aluminum [J].Metallurgical and Materials Transactions A,2015,46(7):2809-2813.
[25] 张成行,曹宇,曹玲飞,等.异种铝合金搅拌摩擦焊接头的显微组织、力学及腐蚀性能 [J].中国有色金属学报,2019,29(10):2255-2265.