非圆齿轮电火花线切割加工工艺参数对齿廓误差的影响

兰州理工大学学报 ›› 2024, Vol. 50 ›› Issue (2): 36-43.

非圆齿轮电火花线切割加工工艺参数对齿廓误差的影响

王亚洲^*, 马晓文, 赵家黎, 陈柏昕, 王真

兰州理工大学机电工程学院, 甘肃兰州 730050

收稿日期:2022-12-28 出版日期:2024-04-28 发布日期:2024-04-29
通讯作者: 王亚洲(1984-),男,甘肃秦安人,副教授,博士.Email:wangyzh@lut.edu.cn
基金资助:
甘肃省自然科学基金(22JR5RA268),国防基础科研计划(JCKY2019427D002)

Influence of electrical parameters on tooth profile error for of non-circular gear WEDM

WANG Ya-zhou, MA Xiao-wen, ZHAO Jia-li, CHEN Bai-xin, WANG Zhen

School of Mechanical and Electrical Engineering, Lanzhou Univ. of Tech., Lanzhou 730050, China

Received:2022-12-28 Online:2024-04-28 Published:2024-04-29

摘要/Abstract

摘要： 线切割加工非圆齿轮时电参数是影响齿廓误差的关键因素之一.设计正交试验,分别采用非圆齿轮齿根、齿廓中部和齿顶的最大齿廓误差对线切割加工非圆齿轮进行分析.通过方差分析方法和主效应分析法,研究线切割加工电参数峰值电流、脉冲宽度、脉冲间隔和跟踪对非圆齿轮齿根、齿廓中部和齿顶的齿廓误差影响规律.同时,对齿廓误差、加工时长和工艺参数进行回归分析,并建立回归模型,基于灰狼优化算法对回归模型进行多目标优化求解.通过研究结果可以得出线切割加工非圆齿轮齿廓不同部位的最优参数组合,可为实际加工提供参考.

关键词: 非圆齿轮, 齿廓误差, 工艺参数, 方差分析, 主效应分析

Abstract: When WEDM machines non-circular gears, electrical parameters are recognized as pivotal factors affecting the tooth profile error of non-circular gears. Orthogonal experiments were designed to analyze WEDM non-circular gears by using the maximum tooth profile errors at the gear tooth root, tooth profile middle and tooth top respectively. Through variance analysis and main effect analysis methods, the influence law of WEDM electrical parameters, including peak current, pulse width, pulse interval, and tracking, on the tooth profile error of non-circular gears at the tooth root, tooth profile middle, and tooth top was studied. At the same time, regression analysis was performed on the tooth profile errors, machining duration, and process parameters to establish regression models. The multi-objective optimization of the regression models was conducted using the Grey Wolf Optimization algorithm. The results of this study obtain the optimal parameter combination for different parts of the WEDM non-circular gear tooth profile, which can provide a reference for actual processing.

Key words: non-circular gear, tooth profile error, process parameters, variance analysis, main effects analysis

中图分类号:

TG484

王亚洲, 马晓文, 赵家黎, 陈柏昕, 王真. 非圆齿轮电火花线切割加工工艺参数对齿廓误差的影响[J]. 兰州理工大学学报, 2024, 50(2): 36-43.

WANG Ya-zhou, MA Xiao-wen, ZHAO Jia-li, CHEN Bai-xin, WANG Zhen. Influence of electrical parameters on tooth profile error for of non-circular gear WEDM[J]. Journal of Lanzhou University of Technology, 2024, 50(2): 36-43.

参考文献

[1] 齿轮手册编委会.齿轮手册 [M].北京:机械工业出版社,2000.
[2] 刘永平, 董志强,董长斌.基于VERICUT的非圆齿轮四轴联动数控插齿加工仿真 [J].机械设计,2021,38(增刊2):95-98.
[3] HO K H,NEWMAN S T,RAHIMIFARD S,et al.State of the art in wire electrical discharge machining (WEDM) [J].International Journal of Machine Tools and Manufacture,2004,44(12/13):1247-1259.
[4] 迟关心,周晶洁,黄瑞宁,等.微细电火花线切割加工误差分析[J].现代制造工程,2006(6):37-40.
[5] 肖帮东,张国军,徐中,等.灰色理论在慢走丝线切割加工中的应用 [J].机械科学与技术,2017,36(1):58-67.
[6] 付雅芳,杨任农,刘晓东,等.基于灰色关联分析的软件工作量估算方法 [J].系统工程与电子技术,2012,34(11):2384-2389.
[7] 宁初刚.单向走丝电火花线切割拐角切割能量控制策略的研究 [D].哈尔滨:哈尔滨工业大学,2011.
[8] HSUE W J,LIAO Y S,LU S S.Fundamental geometry analysis of wire electrical discharge machining in corner cutting [J].International Journal of Machine Tools and Manufacture,1999,39(4):651-667.
[9] 张禹,李文斌,侯志利.电火花线切割粗切拐角误差分析 [J].机械设计与制造,2020,25(11):107-109.
[10] 周晓光,荆晓雪,韩福柱,等.电火花线切割拐角加工精度的实时预测 [J].电加工与模具,2008,14(3):27-30.
[11] 朱宁,许庆平,朱伟根,等.低速走丝电火花线切割加工工艺研究 [J].电工与模具,2008,18(3):59-63.
[12] 陈志.电火花线切割加工工件形位误差的形成机理研究及抑制方法 [D].武汉:华中科技大学,2017.
[13] AZZEH M,NEAGU D,COWLING P I.Fuzzy grey relational analysis for software effort estimation [J].Empirical Software Engineering,2010,15(1):60-90.
[14] 陈晟,奚学程,李子伦,等.电火花线切割小圆弧加工自适应控制 [J].电加工与模具,2022(1):24-28.
[15] 马军,叶红伟,袁杰,等.基于响应面与狼群算法的电火花线切割加工性能与放电能耗建模及优化 [EB/OL].(2022-04-12)[2022-12-22].http://kns.cnki.net/kcms/detail/11.5946.TP.20220411.1049.018.html.