钎焊降温速率对板翅结构钎焊残余应力和等效热变形的影响规律

兰州理工大学学报 ›› 2022, Vol. 48 ›› Issue (1): 65-70.

钎焊降温速率对板翅结构钎焊残余应力和等效热变形的影响规律

代忠华¹, 刘新文², 麻宏强^*3, 王丽³, 张春娥³

1.甘肃第四建设集团有限责任公司, 甘肃兰州 730050;
2.甘肃建投科技研发有限公司, 甘肃兰州 730050;
3.兰州理工大学土木工程学院, 甘肃兰州 730050

收稿日期:2021-04-26 出版日期:2022-02-28 发布日期:2022-03-09
通讯作者: 麻宏强(1984-),男,甘肃静宁人,博士,副教授.Email:mhq2014@sina.com
基金资助:
“十三五”重大科技攻关项目(2016ZX05017-004)

Effect of cooling rate on residual stress and equivalent thermal deformation of brazed plate-fin structures

DAI Zhong-hua¹, LIUXin-wen², MA Hong-qiang³, WANG Li³, ZHANG Chun-e³

1. Gansu Fourth Construction Group Co., Ltd. Lanzhou 730050, China;
2. Gansu Construction Investment Technology R&D Co., Ltd. Lanzhou 730050, China;
3. School of Civil Engineering, Lanzhou Univ. of Tech., Lanzhou 730050, China

Received:2021-04-26 Online:2022-02-28 Published:2022-03-09

摘要/Abstract

摘要： 为了研究不同钎焊降温速率对板翅结构内部的钎焊残余应力和等效弹性热应变的影响规律.建立了板翅结构的三维热应力分析模型,采用热-结构耦合的方法,模拟分析了不同钎焊降温速率下,钎焊残余应力和等效弹性热应变的变化情况.研究结果表明:板翅结构内部的钎焊残余应力随着钎焊降温速率的减小而减小;不同钎焊降温速率下,板翅结构内部的钎焊残余应力之间的差值也不同,当钎焊降温速率小于某一值时,板翅结构内部的钎焊残余应力的大小将近似为定值;钎焊降温速率越小,板翅结构内部薄弱部位发生断裂的风险性就越小;钎焊降温速率对板翅结构的等效弹性热应变的影响较小.

关键词: 钎焊降温速率, 板翅结构, 钎焊残余应力, 等效弹性热应变

Abstract: In order to study the effect of different brazing cooling rate on the brazing residual stress and equivalent elastic thermal strain of plate-fin structure, a three-dimensional thermal stress analysis model of plate-fin structure is established, and the variation of brazing residual stress and equivalent elastic thermal strain under different brazing cooling rates are simulated and analyzed using the thermal-structural coupling method. The results show that the brazing residual stress of fin-structure is decreased with the decrease of the brazing cooling rate. The difference between the brazing residual stresses of the plate-fin structure is also different for different brazing cooling rates, and when the brazing cooling rate is less than a certain value, the brazing residual stress of the plate-fin structure will be approximately constant. The smaller the brazing cooling rate, the smaller the risk of fracture in the weak parts of the plate-fin structure. The brazing cooling rate has little effect on the equivalent elastic thermal strain of the plate-fin structure.

Key words: brazing cooling rate, plate-fin structure, brazing residual stress, equivalent elastic thermal strain

中图分类号:

TE65

代忠华, 刘新文, 麻宏强, 王丽, 张春娥. 钎焊降温速率对板翅结构钎焊残余应力和等效热变形的影响规律[J]. 兰州理工大学学报, 2022, 48(1): 65-70.

DAI Zhong-hua, LIUXin-wen, MA Hong-qiang, WANG Li, ZHANG Chun-e. Effect of cooling rate on residual stress and equivalent thermal deformation of brazed plate-fin structures[J]. Journal of Lanzhou University of Technology, 2022, 48(1): 65-70.

参考文献

[1] SARMIENTO A P,SOARES V,CARQUEJA G G,et al.Thermal performance of diffusion-bonded compact heat exchangers [J].International Journal of Thermal Sciences,2020,153:106384.
[2] SELIMEFENDIGIL F,OZTOP H F.Forced convection and thermal predictions of pulsating nanofluid flow over a backward facing step with a corrugated bottom wall [J].International Journal of Heat & Mass Transfer,2017,110:231-247.
[3] WANG X Y,YAN C,ZHENG Y K,et al.Assessment of chemical kinetic models on hypersonic flow heat transfer [J].International Journal of Heat & Mass Transfer,2017,111:356-366.
[4] PENG H,XIANG L.Optimal design approach for the plate-fin heat exchangers using neural networks cooperated with genetic algorithms [J].Applied Thermal Engineering,2008,28:642-650.
[5] KUZNETSOV V V,SHAMIRZAEV A S.Boiling Heat Transfer for Freon R21 in Rectangular Minichannel [J].Heat Transfer Engineering,2007,28:738-745.
[6] XIE Q Y,LING X.Numerical analysis of residual stress for copper base brazed stainless steel plate-fin structure [J].Journal of Materials Engineering and Performance,2010,19:611-615.
[7] MA H Q,HOU C Q,YANG R X,et al.The influence of structure parameters on stress of plate-fin structures in LNG heat exchanger [J].Journal of Natural Gas Science and Engineering,2016,34:85-99.
[8] MIZOKAMI Y,IGARI T,KAWASHIMA F,et al.Development of structural design procedure of plate-fin heat exchanger for HTGR [J].Nuclear Engineering and Design,2013,255:248-262.
[9] PICARD F,AVEROUS D,JOULIA X,et al.Modelling and dynamic simulation of thermal stresses in brazed plate-fin heat exchanger [J].Computer Aided Chemical Engineering,2006,21:659-664.
[10] 蒋文春,巩建鸣,陈虎,等.不锈钢板翅结构钎焊残余应力及其高温蠕变松弛行为三维有限元分析 [J].焊接学报,2007,28(7):17-20.
[11] 陈虎,巩建鸣,耿鲁阳,等.板翅结构钎焊残余应力与热变形的有限元分析 [J].焊接学报,2006,27(11):29-32.
[12] 周帼彦,涂善东,轩福贞,等.钎焊板翅结构残余应力的分布与优化研究 [J].核动力工程,2010,31(4):101-105.
[13] 蒋文春,巩建鸣,陈虎,等.不锈钢板翅结构钎焊残余应力及其影响因素 [J].金属学报,2008,44(1):105-111.