滚动轧制对7050铝合金FSW接头组织的影响

兰州理工大学学报 ›› 2023, Vol. 49 ›› Issue (4): 30-34.

滚动轧制对7050铝合金FSW接头组织的影响

金玉花^*1,2, 周子正¹, 邢逸初¹, 吴博¹

1.兰州理工大学材料科学与工程学院, 甘肃兰州 730050;
2.兰州理工大学省部共建有色金属先进加工与再利用国家重点实验室, 甘肃兰州 730050

收稿日期:2022-12-27 出版日期:2023-08-28 发布日期:2023-08-29
通讯作者: 金玉花(1971-),女,甘肃榆中人,副教授. Email:yhjin8686@163.com
基金资助:
国家自然科学基金(51865028)

Effect of rolling on microstructure of 7050 aluminum alloy FSW joint

JIN Yu-hua^1,2, ZHOU Zi-zheng¹, XING Yi-chu¹, WU Bo¹

1. School of Materials and Engineering, Lanzhou Univ. of Tech., Lanzhou 730050, China;
2. State Key Laboratory of Advanced Processing and Recycling of Nonferrous Metals, Lanzhou Univ. of Tech., Lanzhou 730050, China

Received:2022-12-27 Online:2023-08-28 Published:2023-08-29

摘要/Abstract

摘要： 采用自制的滚动轧制头对5 mm厚的7050铝合金搅拌摩擦焊接头进行表面滚动轧制处理,并对滚动轧制前后接头的表面粗糙度、变形程度及横截面纵深方向微观组织演化进行了分析.结果表明:滚动轧制后接头的表面粗糙度得到改善,R_a由焊接态的7.45 μm减小至6.82 μm.接头横截面纵深方向从表面向下分为过渡良好的3层,依此为变形层、过渡层及微塑性变形层.变形层是应变最显著的微区,应变呈梯度分布,表层变形最大,随着距接头表面深度的增大而降低.变形层因经历了最大的变形,焊核区原始的等轴状晶粒变形细化,在距接头表面一定深度范围内形成厚度不等的纳米结构.

关键词: 搅拌摩擦焊, 滚动轧制, 表面纳米化, 变形参数, 微观组织

Abstract: The 5 mm-thick joint of 7050 aluminum alloy friction stir welding was rolled by self-made rolling tool on the surface, and the surface roughness, deformation degree and microstructure evolution of the joints before and after rolling were analyzed. The results showed that the surface roughness of the joint is improved after rolling, and R_a decreases from 7.45 μm as-welded to 6.82 μm. The depth direction of the joint is divided into three layers from the surface down, which are the deformation layer, transition layer and microplastic deformation layer. The deformation layer is the microregion with the most significant strain, the strain of which shows the gradient distribution. The surface deformation is the largest and decreases with increasing depth from the joint surface. The deformed layer undergoes maximum deformation as a result of which the original isoaxial grain in the nugget zone is deformed and refined, forming nanostructures of varying thickness within a certain depth from the joint surface.

Key words: friction stir welding, rolling, surface nanocrystallization, deformation parameters, microstructure

中图分类号:

TG453

金玉花, 周子正, 邢逸初, 吴博. 滚动轧制对7050铝合金FSW接头组织的影响[J]. 兰州理工大学学报, 2023, 49(4): 30-34.

JIN Yu-hua, ZHOU Zi-zheng, XING Yi-chu, WU Bo. Effect of rolling on microstructure of 7050 aluminum alloy FSW joint[J]. Journal of Lanzhou University of Technology, 2023, 49(4): 30-34.

参考文献

[1] 张华,郭启龙,赵常宇,等.双级时效对7050-T7451铝合金搅拌摩擦焊组织及应力腐蚀敏感性的影响 [J].焊接学报,2020,41(6):1-5,97.
[2] 贺地求,薛飞,孙友庆.C18150合金搅拌摩擦焊焊缝微观组织与力学性能分析 [J].焊接学报,2019,40(11):93-99.
[3] 王磊,易幼平,黄始全,等.固溶前深冷变形处理对7050铝合金组织和性能的影响 [J].材料导报,2019,33(20):3467-3471.
[4] MA C Q,HOU L G,ZHANG J S,et al.Effect of deformation routes on the microstructures and mechanical properties of the asymmetrical rolled 7050 aluminum alloy plates [J].Materials Science and Engineering A,2018,773:304-315.
[5] 王磊,付强,安金岚,等.2A12-T4铝合金搅拌摩擦焊多区域疲劳裂纹扩展行为 [J].焊接学报,2021,42(2):24-29.
[6] LEE H H,YOON J I,PARK H K,et al.Unique microstructure and simultaneous enhancements of strength and ductility in gradient-microstructured Cu sheet produced by single-roll angular-rolling[J].Acta Materialia,2019,166:638-649.
[7] 王强,高国强,罗学昆.激光喷丸与机械喷丸复合强化对2124-T851铝合金疲劳寿命的影响 [J].表面技术,2021,50(4):96-102.
[8] CHAN H L,RUAN H H,CHEN A Y,et al.Optimization of the strain rate to achieve exceptional mechanical properties of 304 stainless steel using high speed ultrasonic surface mechanical attrition treatment [J].Acta Materialia,2010,58(15):5086-5096.
[9] LEI Y B,WANG Z B,XU J L,et al.Simultaneous enhancement of stress-and strain-controlled fatigue properties in 316L stainless steel with gradient nanostructure [J].Acta Materialia,2019,168(15):133-142.
[10] HEILMANN P,RIGNEY D A.An energy-based model of friction and its application to coated systems [J].Wear,1981,72(2):195-217.
[11] MARTINEZ-ESNAOLA J M,MONTAGNAT M,DUVAL P,et al.Geometrically necessary dislocations in a c-axis oriented cylindrical bar of basal-slipping hexagonal crystals deformed in torsion [J].Scripta Materialia,2004,50(2):273-278.
[12] LU K.Stabilizing nanostructures in metals using grain and twin boundary architectures [J].Nature Reviews Materials,2016,1(5):1-13.